The Type 40 Series allows a driving diameter of 0.32" to 0.67". The driving pins move independently to allow a five-degree pitch of the end face of the work-piece. The mechanical compensation and lock down center point allow a constant length to be held from center to the taper. The Type 40 Series is available in 3, 4,and 5 morse taper designs as well as a flange mount. Chuck mounting can be achieved as described in the mounting procedures.View Catalog Page

The Type 41 Series allows a driving diameter of 0.24" to 0.75". The driving pins move independently to allow a five-degree pitch of the end face of the work-piece. The mechanical compensation and lock down center point allow a constant length to be held from center to the taper. The Type 41 Series is available in 3, 4,and 5 morse taper designs as well as a flange mount. Chuck mounting can be achieved as described in the mounting procedures. View Catalog Page

The Type 42 Series allows a driving diameter of 0.43" to 0.79". The driving pins move independently to allow a five-degree pitch of the end face of the work-piece. The mechanical compensation and lock down center point allow a constant length to be held from center to the taper. The Type 42 Series is available in 3, 4,and 5 morse taper designs as well as a flange mount. Chuck mounting can be achieved as described in the mounting procedures. View Catalog Page

The Type 43 Series allows a driving diameter of 0.51" to 1.02". The driving pins move independently to allow a five-degree pitch of the end face of the work-piece. The mechanical compensation and lock down center point allow a constant length to be held from center to the taper. The Type 43 Series is available in 3, 4,and 5 morse taper designs as well as a flange mount. Chuck mounting can be achieved as described in the mounting procedures. View Catalog Page

The Type 44 Series allows a driving diameter of 1.02" to 1.42". The driving pins move independently to allow a five-degree pitch of the end face of the work-piece. The mechanical compensation and lock down center point allow a constant length to be held from center to the taper. The Type 44 Series is available in 4 and 5 morse taper designs as well as a flange mount. Chuck mounting can be achieved as described in the mounting procedures. View Catalog Page

The Type 45 Series allows a driving diameter of 1.34" to 1.73". The driving pins move independently to allow a five-degree pitch of the end face of the work-piece. The mechanical compensation and lock down center point allow a constant length to be held from center to the taper. The Type 45 Series is available in 4 and 5 morse taper designs as well as a flange mount. Chuck mounting can be achieved as described in the mounting procedures. View Catalog Page

The Type 46 Series allows a driving diameter of 1.14" to 1.93". The driving pins move independently to allow a five-degree pitch of the end face of the work-piece. The mechanical compensation and lock down center point allow a constant length to be held from center to the taper. The Type 46 Series is available in a flange mount. Chuck mounting can be achieved as described in the mounting procedures. View Catalog Page

The Type 47 Series allows a driving diameter of 1.54" to 2.32". The driving pins move independently to allow a five-degree pitch of the end face of the work-piece. The mechanical compensation and lock down center point allow a constant length to be held from center to the taper. The Type 47 Series is available in 5 and 6 morse taper designs as well as a flange mount. Chuck mounting can be achieved as described in the mounting procedures. View Catalog Page

The Type 48 Series allows a driving diameter of 1.93" to 2.72". The driving pins move independently to allow a five-degree pitch of the end face of the work-piece. The mechanical compensation and lock down center point allow a constant length to be held from center to the taper. The Type 48 Series is available in a flange mount. Chuck mounting can be achieved as described in the mounting procedures. View Catalog Page

The Type 49 Series allows a driving diameter of 2.72" to 3.90". The driving pins move independently to allow a five-degree pitch of the end face of the work-piece. The mechanical compensation and lock down center point allow a constant length to be held from center to the taper. The Type 49 Series is available in a flange mount. Chuck mounting can be achieved as described in the mounting procedures. View Catalog Page